Current sensor chips: ACS712ELC-20A; Power supply: 5V; The module can measure the positive and negative 20A corresponding to the analog output 100mV / A A product for Arduino that works with official Arduino boards.
Please refer to: http://dx.com/p/30a-acs712-current-sensor-module-158589 - Module: ACS712 - Material: PCB - Chipset: ACS712ELC-30A - Voltage: 5V - +/-30A current measurement - Great for DIY project
Model: D108061 - Quantity: 1 - Color: Blue - Material: FR4 + PCB - Current sensor chip: ACS712ELC-30A - Pin 5V power supply on-board power indicator - The module can measure the positive and negative 30A current corresponding to the analog output 66mV/A - No test current through the output voltage is VCC / 2; - Can be used to upgrade the devices such as DVD / router / hard drive - Packing list: - 1 x Current sensor module
Color: Blue - Material: PCB + metal - ACS712ELC-20A sensor chipset - Powered by 5V power supply - On-board power indicator - Measures -20~+20A current corresponding simulation output 100mV/A - Output voltage is VCC/2 when on current was measured - ACS712 is based on the principle of Hall detection please avoid the magnetic field affect when using it - Datasheet: http://m2.img.dxcdn.com/CDDriver/sku.206997.rar
OPEN-SMART High Quality ACS712 20A Current Sensor Module for Arduino
Module features: Jog type: the initial state is low high touch do not touch is low; Low power consumption; Operating voltage: DC 2.5~5.5V; Touch surface can be used as positive and negative can replace the traditional touch of a button; 4 x M2 screw holes easy for operation; Specifications: Power voltage VCC: 2.0~5.5V Output High VOH: 0.8V Output LOW VOL: 0.3V Output Pin Sink Current (@ VCC = 3V VOL = 0.6V): 8mA Output pin pull-up current (@ VCC = 3V VOH = 2.4V):-4mA Response time (low power mode): 220mS Response Time (Fast mode): 60mS Control Interface: three pins (GND VCC SIG) GND to ground VCC is power supply SIG digital signal output pin; Power Indicator: Green LED power on the right is shiny; Touch area: Similar to a fingerprint icon inside the area you can touch the trigger finger. Positioning holes : 4 X M2 screws positioning hole diameter is 2.2mm the positioning of the module is easy to install to achieve inter- module combination; A product for Arduino that works with official Arduino boards.
Chip: L3G4200D; Power supply: 3~5V; Communication methods: IIC / SPI communication protocol; Measuring range: 250 / 500 / 2000 dps For gaming virtual reality input device motion control HMI GPS electrical equipment and robotics
ADXL335 is a small size low power consumption three axis accelerometer providing the voltage output of signal disposal it can measure +/- 3g magnetic field full-scale acceleration minimum. It can measure skew detection of the application of static gravity acceleration and sports impact or vibration acceleration in dynamic. Three-axis magnetic field accelerometer module Compact size low power supply Used for game systems mobile devices etc Sensor Chip: ADXL335 Operating Voltage Range: 3V ~ 5V Supply Current: 400uA Interface: Analog quantity output Operating Temperature: -40'C~ +85'C Sensitivity: 300mv /g; Sensitivity of accuracy (%): +/- 10
OPEN-SMART ACS712 30A Current Sensor Module for Arduino
Color: Blue - Material: PCB + metal - ACS712ELC-05B sensor chipset - Powered by 5V power supply - On-board power indicator - Measures -5~+5A current corresponding simulation output 185mV/A - Output voltage is VCC/2 when on current was measured - ACS712 is based on the principle of Hall detection please avoid the magnetic field affect when using it - Datasheet: http://m2.img.dxcdn.com/CDDriver/sku.206997.rar
Specifications: Power supply voltage VCC: 3.2~5.25V; Pull-up current (@ high = 5V): 1.3mA; High Input: 3~VCC + 0.3V; Low-level input: -0.3~+0.7V; IR emission distance: 10m; Interface Description: Control Interface: Total of three pins (GND VCC SIG) GND to ground VCC is the power supply SIG is the signal input pin. Infrared emission: emission wavelength of 940nm can be infrared signal. Groove: easy adjustment infrared emission direction manually. Positioning holes: 4 x M2 screws positioning hole diameter is 2.2mm the positioning of the module is easy to install to achieve inter-module combination; A product for Arduino that works with official Arduino boards.
Based on a current sensor module and based on the principle of the hall current which convert current into an analog voltage output; MCU (Arduino UNO R3) that includes AD converter can be read out and converted into measured current value; Suitable for SCM system powered by 5V power supply; Can measure AC and DC; Widely used in over-current detection current monitoring and other occasions.
OPEN-SMART High Quality ACS712 5A Current Sensor Module for Arduino
The product measures acceleration with a minimum full-scale range of +/-3 g; Based on ADI this is the latest and proven line of analog sensors w/ precision accelerometers Operating Voltage Range: 1.8V ~ 3.6V; Sensitivity: 300mv /g; Sensitivity of accuracy (%): +/- 10; Typical bandwidth: 1.6KHz; Breakout module 3 axis sensing; High sensitive 10000g shock survival; BW adjustment with a single capacitor per axis; Complete 3 axis Accelerate module A product for Arduino that works with official Arduino boards.